Standards referred to

Note: Any reference to European Standards in this section must be taken to include reference to the relevant Irish National Annex.

Standards referred to:

I.S. 193:2006 Timber trusses for roofs

prS.R. 325:yyyy Recommendations for the design of masonry structures in Ireland to Eurocode 6 (to be published by NSAI)

I.S. 440:2009 Timber frame dwellings (under revision)

I.S. EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements

I.S. EN 206-1:2002 Concrete - Part 1: Specification, performance, production and conformity

I.S. EN 336:2003 Structural timber - Sizes, permitted deviations

I.S. EN 338:2009 Structural timber - Strength classes

I.S. EN 771-1:2011 Specification for masonry units - Part 1: Clay masonry units

I.S. EN 771-2:2011 Specification for masonry units - Part 2: Calcium silicate masonry units

I.S. EN 771-3:2011 Specification for masonry units - Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)

I.S. EN 771-4:2011 Specification for masonry units - Part 3: Autoclaved aerated concrete masonry units

I.S. EN 771-5:2011 Specification for masonry units - Part 5: Manufactured stone masonry units

I.S. EN 771-6:2011 Specification for masonry units - Part 6: Natural stone masonry units

I.S. EN 772-1:2011 Methods of test for masonry units - Part 1: determination of compressive strength

I.S. EN 845-1:2003+A1:2008 Specification for ancillary components for masonry - Part 1: Ties, tension straps, hangers and brackets

I.S. EN 845-2:2003 Specification for ancillary components for masonry - Part 2: Lintels

I.S. EN 998-2:2010 Specification for mortar for masonry - Part 2: Masonry mortar

I.S. EN 1090-1:2009/AC:2010 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components

I.S. EN 1090-2:2008+A1:2011 Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures

I.S. EN 1090-3:2008 Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures

I.S. EN 1536:2010 Execution of special geotechnical work - Bored piles

I.S. EN 1537:2000 Execution of special geotechnical work - Ground anchors

I.S. EN 1538:2010 Execution of special geotechnical work - Diaphragm walls

I.S. EN 1912:2004 + A4:2010 Structural timber - Strength classes - Assignment of visual grades and species

I.S. EN 12063:1999 Execution of special geotechnical work - Sheet pile walls

I.S. EN 12699:2000 Execution of special geotechnical work - Displacement piles

I.S. EN 12620:2002 Aggregates for concrete

I.S. EN 12715:2000 Execution of special geotechnical work - Grouting

I.S. EN 12716:2001 Execution of special geotechnical work - Jet grouting

I.S. EN 13670:2009 Execution of concrete structures

I.S. EN 14199:2005 Execution of special geotechnical work - Micropiles

I.S. EN 14475:2006/ COR 2006 Execution of special geotechnical work - Reinforced fill

I.S. EN 14490: 2010 Execution of special geotechnical work - Soil nailing

I.S. EN 14679:2005/ COR 2006 Execution of special geotechnical work - Deep mixing

I.S. EN 14731:2005 Execution of special geotechnical work - Ground treatment by deep vibration

I.S. EN 15237:2007 Execution of special geotechnical work - Vertical drainage

S.R. 16:2004 Guidance on the use of I.S. EN 12620:2002 - Aggregates for concrete

BS 1297: 1987 Specification for tongued and grooved softwood flooring

BS 5080-1:1994 Structural fixings in concrete and masonry - Part 1: Method of test for tensile loading

BS 5080-2:1986 Structural fixings in concrete and masonry - Part 2: Method of determination of resistance to loading in shear (AMD 7602)

BS 5427-1: 1996 Code of practice for the use of profiled sheet for roof and wall cladding on buildings - Part 1: Design

BS 5516-1:2004 Patent glazing and sloping glazing for buildings - Part 1: Code of practice for design and installation of sloping and vertical patent glazing

BS 5516-2:2004 Patent glazing and sloping glazing for buildings - Part 2: Code of practice for sloping glazing

BS 6262: 1982 Code of practice for glazing for buildings AMD 4063; AMD 4582; AMD 8279 (Partially superseded but remains current)

BS 6262-1:2005 Glazing for buildings Part 1: General methodology for the selection of glazing

BS 6262-2:2005 Glazing for buildings Part 2: Code of practice for energy, light and sound

BS 6262-3:2005 Glazing for buildings Part 3: Code of practice for fire, security and wind loading

BS 6262-4: 2005 Glazing for buildings Part 4: Code of practice for safety related to human impact

BS 6262-5: 2005 Glazing for buildings Part 5: Code of practice for frame design considerations

BS 6262-6: 2005 Glazing for buildings Part 6: Code of practice for special applications

BS 6262-7: 2005 Glazing for buildings Part 7: Provision of information

BS 6750: 1986 Specification for modular co-ordination in building

BS 8200: 1985 Code of practice for design of non-loadbearing external vertical enclosures of buildings

BS 8297: 2000 Code of practice for design and installation of non-loadbearing precast concrete cladding AMD 11064, AMD 13018

BS 8298-1:2010 Code of practice for design and installation of natural stone cladding and lining - Part 1: General

BS 8298-2:2010 Code of practice for the design and installation of natural stone cladding and lining - Part 2: Traditional handset external cladding

BS 8298-3:2010 Code of practice for the design and installation of natural stone cladding and lining - Part 3: Stone-faced pre-cast concrete cladding systems

BS 8298-4:2010 Code of practice for the design and installation of natural stone cladding and lining - Part 4: Rainscreen and stone on metal frame cladding systems

BS 8298-5: (In preparation) Code of practice for the design and installation of natural stone cladding and lining - Part 5: Internal linings

Structural Eurocodes

Eurocode

I.S. EN 1990:2002 + A1 2005 Eurocode - Basis of structural design

Eurocode 1

I.S. EN 1991-1-1:2002+A1 2005 Eurocode 1 - Actions on structures - Part 1-1: General actions - Densities, self-weight, imposed loads for buildings

I.S. EN 1991-1-3:2003 Eurocode 1 - Actions on structures - Part 1-3: General actions - Snow loads

I.S. EN 1991-1-4:2005+A1 2010 Eurocode 1 - Actions on structures - Part 1-4: General actions - Wind actions

I.S. EN 1991-1-5:2003 Eurocode 1 - Actions on structures - Part 1-5: General actions - Thermal actions

I.S. EN 1991-1-6:2005 Eurocode 1 - Actions on structures - Part 1-6: General actions - Actions during execution

I.S. EN 1991-1-7:2006 Eurocode 1 - Actions on structures - Part 1-7: General actions - Accidental actions

I.S. EN 1991-3:2006 Eurocode 1 - Actions on structures - Part 3: Actions induced by cranes and machinery

Eurocode 2

I.S. EN 1992-1-1:2005 Eurocode 2 - Design of concrete structures - Part 1-1: General rules and rules for buildings

I.S. EN 1992-3:2006 Eurocode 2 - Design of concrete structures - Part 3: Liquid retaining and containing structures

Eurocode 3

I.S. EN 1993-1-1:2005 Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings

I.S. EN 1993-1-3:2006 Eurocode 3 - Design of steel structures - Part 1-3: General rules - Supplementary rules for cold formed members and sheeting

I.S. EN 1993-1-4:2006 Eurocode 3 - Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels

I.S. EN 1993-1-5:2006 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements

I.S. EN 1993-1-6:2007 Eurocode 3 - Design of steel structures - Part 1-6: General - Strength and stability of shell structures

I.S. EN 1993-1-7:2007 Eurocode 3 - Design of steel structures - Part 1-7: Plated structures subject to out of plane loading

I.S. EN 1993-1-8:2005 Eurocode 3 - Design of steel structures - Part 1-8: Design of joints

I.S. EN 1993-1-9:2005 Eurocode 3 - Design of steel structures - Part 1-9: Fatigue

I.S. EN 1993-1-10:2005 Eurocode 3 - Design of steel structures - Part 1-10: Material toughness and through-thickness properties

I.S. EN 1993-1-11:2006 Eurocode 3 - Design of steel structures - Part 1-11: Design of structures with tension components

I.S. EN 1993-1-12:2007 Eurocode 3 - Design of steel structures - Part 1-12: Additional rules for the extension of EN 1993 up to grades S700

I.S. EN 1993-5:2007 Eurocode 3 - Design of steel structures - Part 5: Piling

I.S. EN 1993-6:2007 Eurocode 3 - Design of steel structures - Part 6: Crane supporting structures

Eurocode 4

I.S. EN 1994-1-1: 2005 Eurocode 4 - Design of composite concrete and steel structures - Part 1-1: General rules and rules for buildings

Eurocode 5

I.S. EN 1995-1-1:2005+A1:2008 Eurocode 5 - Design of timber structures - Part 1-1: Common rules and rules for buildings

Eurocode 6

I.S. EN 1996-1-1:2005 Eurocode 6 - Design of masonry structures - Part 1-1: Rules for reinforced and un-reinforced masonry

I.S. EN 1996-2:2006 Eurocode 6 - Design of masonry structures - Part 2: Design considerations, selection of materials and execution

I.S. EN 1996-3:2006 Eurocode 6 - Design of masonry structures - Part 3: Simplified calculations methods

Eurocode 7

I.S. EN 1997-1: 2005 Eurocode 7 - Geotechnical design - Part 1: General rules

I.S. EN 1997-2: 2005 Eurocode 7 - Geotechnical design - Part 2: Ground investigation and testing

Eurocode 9

I.S. EN 1999-1-1:2007+A1:2009 Eurocode 9 - Design of aluminium structures - Part 1-1: General structural rules

I.S. EN 1999-1-3:2007 Eurocode 9 - Design of aluminium structures - Part 1-3: Additional rules for structures susceptible to fatigue

I.S. EN 1999-1-4:2007 Eurocode 9 - Design of aluminium structures - Part 1-4: Supplementary rules for trapezoidal sheeting

I.S. EN 1999-1-5:2007 Eurocode 9 - Design of aluminium structures - Part 1-5: Supplementary rules for shell structures

Publications referred to:

Appraisal of existing structures 3rd edition, Institution of Structural Engineers 2010

Building Research Establishment Digest 366: Structural appraisal of existing buildings for change of use 1991

Code of practice for the design and installation of anchors - Health and Safety Authority 2010

ETAG No. 001 1997

ETAG 001 Edition 1997 Guideline for European Technical Approvals of Metal Anchors for use in Concrete - Amended November 2006, European Organisation for Technical Approvals (EOTA) http://www.eota.be

ETAG 029 Edition 2010 Guideline for European Technical Approval of metal injection anchors for use in masonry, European Organisation for Technical Approvals (EOTA) http://www.eota.be

Structural renovation of traditional buildings, Report 111 Construction Industry Research and Information Association (1994 reprint with amendments)

External Timber Cladding 2nd Edition 2007, TRADA

Other standards and publications

BS 6180: 2011 Barriers in and about buildings - Code of practice

BS 8219: 2001 Installation of sheet roof and wall coverings - Profiled fibre cement - Code of practice

Practical guide to structural robustness and disproportionate collapse in buildings, Institution of Structural Engineers 2010